保质期：18个月包装说明： 支装：60克；注意事项：1.尽量放置于阴凉处，避免阳光照射；2.用后应立即盖好，避免接触灰尘等杂物；3.导热硅脂的涂抹厚度在充分覆盖的情况下，越薄越好（大约A4打印纸厚度）。

保质期：18个月包装说明： 支装：45克；注意事项：1.尽量放置于阴凉处，避免阳光照射；2.用后应立即盖好，避免接触灰尘等杂物；3.导热硅脂的涂抹厚度在充分覆盖的情况下，越薄越好（大约A4打印纸厚度）。

Introduction Thermal grease is kind of uniform pasty substance which composes thermally conductive filler,high-temperature synthetic oil,stabilizer and additive. The color is white and grey . It is used in the place between the heating element and cooling device.The radiator needs mechanical immobilization.The obviously advantage is its price and easy to repair.It can wet the heat sink and the device surface,reduce the thermal resistance contacting,so its suitable for large power cooling device.Application① It is widely used in various electronic products, and the contact surface between the heating element and the heat radiating device in the electrical equipment② It is used in the contact surface between the radiator of the LED lamp and the PCB. Suitable for SMD and COB lamp③ CPU, power amplifier, thermistor, power module, etc.Caution① Please note that the thickness of the thermal grease will affect the efficiency of heat conduction, so please coat moderate quantity on the objects surface., and the thinner, the better② Keep away from children③ If contact with the skin, wipe clean, and then rinse with water; if contact with eyes, immediately wash with water, and go to the hospital to checkPacking① 1K· 1KG/ barrel, 12KG/ box② 300ml/ tube (500g/tube), 25 PCS / box③ 25KG/ barrel④ Customized special packageStorage And Transport① This product should be stored in a dry, cool place, avoid rain, sun exposure, storage period of 12 months（25℃）. During storage, a small amount of silicone oil may outflow, and this is a normal state, does not affect the use of results. If necessary, should be used after mixing evenly.② Such products are non hazardous and can be transported in general chemicals

Introduction Electronic RTV silicone sealant is a single component room temperature curing silicone rubber, which has good adhesion For metal, glass, plastics and other materials. The silica gel is elastomer after cured, which has anti cold alternate and aging resistance and insulation properties. The silica gel has excellent moisture resistance, high temperature resistance, earthquake resistance, corona resistance, anti leakage performance, which comply with RoHs directive requirementsApplication① Insulation seal for electrical switch② Insulation seal for relays and other electronic components③ LED lamp adhesive, waterproof, insulation, sealingCaution① This product is non-toxic after completely cured , but should avoid contact with the eyes and children before curing② working area maintain ventilation③ If contact with the skin, wipe clean, and then rinse with water; if contact with eyes, immediately wash with water, and go to the hospital to checkPacking① 50 ml/tube, 200 tube/box② 300 ml/tube，25 tube/box③ 2600 ml/tube，4 tube/box④ Customized special packageStorage And Transport① This product should be stored in a dry, cool place, avoid rain, sun exposure, storage period of six months（25℃）。② Such products are non hazardous and can be transported in general chemicals

IntroductionTwo-component silicone is distinguished and named for the single component silica gel.This product consists of two compnents and cures after mixing the two components in the right proportion.Generally divided into Condensation type and Addition type,the biggest difference between the two is Condensation type will release low-molecular substance and Addition type will not,So Condensation type potting will shrink during curing and Addition type potting will not.ApplicationIt can use in the high power electronic components, modular power supplies and circuit boards for potting protection,which has good heat conduction and temperature resistance. Such as LED driver power ,automotive HID lamp module power supply, automotive ignition system module power supply, network transformers, etc.InstructionBefore use, the A component and B component in their respective containers fully mixing evenly, and then according to the weight ratio of A:B=1:1, put into the mixing tank mixing evenlyPut the mixture into the container. Curing at room temperature or heating. In the winter, it will take a long time to cure,suggested by heating curing, curing under 80℃ for 15-30 minutes , and at room temperature, generally takes about 3~5 hours curing.Caution① Glue should be sealed storage. The mixture should be used once to avoid waste② This product is not dangerous, but do not eat and into the eyes.③ After a long period of storage, there will be precipitation in the glue. Please mix evenly to use and does not affect the performance④ Glue exposure to a certain amount of the following chemical substances will make the glue does not solidify ( little amount of the following substances will not affect the curing)N, P, S organic compoundsIonic compounds of Sn, Pb, Hg, As and other elementsContaining alkynes and vinyl compoundsIn order to avoid the above phenomenon, the use of the circuit board as far as possible to wipe clean the remaining rosin, try to use low lead content of solder. It can also use three anti - paint soaked, and then use glue⑤ Before a large amount of use，Please try a small amount of trial to confirm Is it appropriatePacking50Kg/setCustomized special packageStorage And Transport① This product storage period of 3-6 months（25℃）.② Such products are non hazardous and can be transported in general chemicals

Introduction Thermal grease is kind of uniform pasty substance which composes thermally conductive filler,high-temperature synthetic oil,stabilizer and additive. The color is white and grey . It is used in the place between the heating element and cooling device.The radiator needs mechanical immobilization.The obviously advantage is its price and easy to repair.It can wet the heat sink and the device surface,reduce the thermal resistance contacting,so its suitable for large power cooling device.Application① It is widely used in various electronic products, and the contact surface between the heating element and the heat radiating device in the electrical equipment② It is used in the contact surface between the radiator of the LED lamp and the PCB. Suitable for SMD and COB lamp③ CPU, power amplifier, thermistor, power module, etc.Caution① Please note that the thickness of the thermal grease will affect the efficiency of heat conduction, so please coat moderate quantity on the objects surface., and the thinner, the better② Keep away from children③ If contact with the skin, wipe clean, and then rinse with water; if contact with eyes, immediately wash with water, and go to the hospital to checkPacking① 1K· 1KG/ barrel, 12KG/ box② 300ml/ tube (500g/tube), 25 PCS / box③ 25KG/ barrel④ Customized special packageStorage And Transport① This product should be stored in a dry, cool place, avoid rain, sun exposure, storage period of 12 months（25℃）. During storage, a small amount of silicone oil may outflow, and this is a normal state, does not affect the use of results. If necessary, should be used after mixing evenly.② Such products are non hazardous and can be transported in general chemicals